Don't underestimate small capacitors. His function is very significant. Have you ever used his electronic products? They can be ugly everywhere if not used well, so first, we will introduce the function of capacitors. As one of the passive components, capacitors have the following functions:
1. Applied to power circuits to achieve the functions of capacitors in bypass, decoupling, filtering, and energy storage, the following categories are detailed:
1) Filtering
Filtering is an important part of the function of capacitors. It is used in almost all power circuits. In theory (assuming that the capacitance is pure), the larger the capacitance, the smaller the impedance, and the higher the frequency of passage. But in fact, most capacitors exceeding 1uF are electrolytic capacitors with a large inductance component, so when the frequency is high, the impedance will actually increase. Sometimes you may see a large electrolytic capacitor connected in parallel with a small capacitor, where the large capacitor is connected to low frequency and the small capacitor is connected to high frequency. The function of a capacitor is to pass through high resistance and low resistance, while passing through high frequency and low frequency resistance. The larger the capacitance, the easier it is to pass through low frequencies, and the larger the capacitance, the easier it is to pass through high frequencies. Specifically used in filtering, large capacitors (1000uF) filter low frequencies and small capacitors (20pF) filter high frequencies.
Some netizens once compared the filtering capacitor to a "pond". Due to the fact that the voltage at both ends of the capacitor does not suddenly change, it can be seen that the higher the signal frequency, the greater the attenuation. It can be vividly said that the capacitor is like a pond, without any changes in water volume caused by the addition or evaporation of a few drops of water. It converts changes in voltage into changes in current, and the higher the frequency, the greater the peak current, thereby buffering the voltage. Filtering is the process of charging and discharging.
2) Bypass
Bypass capacitors are energy storage devices that provide energy to local devices, which can homogenize the output of the voltage regulator and reduce load demand. Just like a small rechargeable battery, the bypass capacitor can be charged and discharged into the device. To minimize impedance, the bypass capacitor should be as close as possible to the power supply pin and ground pin of the load device. This can effectively prevent ground potential rise and noise caused by excessive input values. A ground bomb is the voltage drop when the ground connection passes through a large current burr.
3) Removing lotus root
Removing lotus roots, also known as uncoupling lotus roots. From a circuit perspective, it is always possible to distinguish between the source of the drive and the load being driven. If the load capacitance is relatively large, the driving circuit needs to charge and discharge the capacitance in order to complete the signal jump. When the rising edge is steep, the current is relatively high, so the driving current will absorb a large amount of power current. Due to the inductance and resistance in the circuit (especially the inductance on the chip pins, it will rebound), this current is actually a type of noise compared to normal conditions, It will affect the normal operation of the previous level. This is coupling. The decoupling capacitor serves as a battery to meet the changes in driving circuit current and avoid mutual coupling interference. Combining bypass capacitors with decoupling capacitors will be easier to understand. The bypass capacitor is actually decoupled, but it generally refers to high-frequency bypass, which means adding a low impedance leakage path to high-frequency switching noise.The high-frequency bypass capacitor is generally relatively small, based on the resonance frequency of 0.1u, 0.01u, etc., while the decoupling capacitor is generally larger, which is 10uF or greater, determined by the distributed parameters in the circuit and the variation of the driving current. Bypass is to filter out the interference in the input signal, while decoupling is to filter out the interference in the output signal, preventing the interference signal from returning to the power source. This should be their fundamental difference.
4) Energy storage
Energy storage capacitors collect charges through rectifiers and transmit the stored energy to the output of the power supply through converter leads. Aluminum electrolytic capacitors with voltage ratings ranging from 40 to 450VDC and capacitance values ranging from 220 to 150 000uF (such as EPCOS B43504 or B43505) are commonly used. According to different power supply requirements, devices may sometimes be in series, parallel, or their combination. For power supplies with power levels exceeding 10KW, larger can shaped spiral terminal capacitors are usually used.
2. Applied in signal circuits, it mainly performs the functions of coupling, oscillation/synchronization, and time constant:
1) Coupling
For example, the emitter of a transistor amplifier has a self-sufficient bias resistor, which simultaneously generates voltage drop feedback to the input terminal, forming input output signal coupling. This resistor is the component that generates coupling. If a capacitor is connected in parallel at both ends of this resistor, due to the smaller impedance of the AC signal caused by the capacitor with appropriate capacity, the coupling effect generated by the resistor is reduced, Therefore, this capacitor is called a decoupling capacitor.
2) Oscillation/synchronization
The load capacitors including RC, LC oscillators, and crystals all belong to this category.
3) Time constant
This is a common integral circuit composed of R and C in series. When the input signal voltage is applied to the input terminal, the voltage on the capacitor (C) gradually increases. And its charging current decreases with the increase of voltage. The characteristics of current passing through resistance (R) and capacitance (C) are described by the following formula:
I=(V/R) e - (t/CR)
After we understand the role of capacitors, let's talk about the precautions for capacitors in use:
A. What is a good capacitor.
1. The larger the capacitance, the better.
Many people often prefer to use large capacity capacitors in the replacement of capacitors. We know that although the larger the capacitance, the stronger the current compensation ability provided for the IC. Not to mention the increase in capacitor capacity brings about a larger volume, which increases costs and also affects air flow and heat dissipation. The key lies in the presence of parasitic inductance on the capacitor, and the capacitor discharge circuit will resonate at a certain frequency point. At the resonance point, the impedance of the capacitor is small. Therefore, the impedance of the discharge circuit is the smallest, and the effect of supplementing energy is also the best. But when the frequency exceeds the resonance point, the impedance of the discharge circuit begins to increase, and the capacitance's ability to provide current begins to decrease. The larger the capacitance value of the capacitor, the lower the resonant frequency, and the smaller the frequency range in which the capacitor can effectively compensate for the current.From the perspective of ensuring the ability of capacitors to provide high-frequency current, the viewpoint that larger capacitors are better is incorrect. Generally, there is a reference value in circuit design.
2. For capacitors of the same capacity, the more small capacitors connected in parallel, the better.
Voltage withstand value, temperature resistance value, capacitance value, ESR (equivalent resistance), etc. are several important parameters of capacitors, and the lower the ESR, the better. ESR is related to the capacity, frequency, voltage, temperature, etc. of capacitors. When the voltage is fixed, the larger the capacity, the lower the ESR. The use of multiple small capacitors connected in parallel in board design is a limitation of PCB space. Some people believe that the more small resistors connected in parallel, the lower ESR, and the better the effect. In theory, this is the case, but considering the impedance of the capacitor pin solder joint, using multiple small capacitors in parallel may not necessarily result in outstanding results.
The lower the ESR, the better the effect.
Based on our improved power supply circuit, for the input capacitor, the capacity of the input capacitor should be slightly larger. The requirement for relative capacity can be appropriately reduced for ESR. Because the input capacitor is mainly used for withstand voltage, followed by absorbing MOSFET switching pulses. For output capacitors, the requirements and capacity for withstand voltage can be appropriately reduced. The requirements for ESR are a bit higher because what needs to be ensured here is sufficient current flow. But it should be noted that the lower the ESR, the better. Low ESR capacitors can cause switching circuit oscillations. The complexity of the vibration suppression circuit can also lead to an increase in cost. In board design, there is usually a reference value here, which serves as a parameter for component selection to avoid cost increases caused by vibration reduction circuits.
4. Good capacitors represent high quality.
The theory of "only capacitance" was once in its heyday, and some manufacturers and media deliberately made this matter a selling point. In board design, the level of circuit design is crucial. Just like some manufacturers who can use two-phase power supply to produce more stable products than some manufacturers who use four-phase power supply, blindly using expensive capacitors may not necessarily result in good products. When measuring a product, it is necessary to consider it from all angles and perspectives, and the role of capacitors should not be intentionally or unintentionally exaggerated.
B. Face to face interview with capacitor explosion
Types of explosive slurry: There are two types: input capacitor explosive slurry and output capacitor explosive slurry.
For input capacitors, what I mean is C1, which filters the current received by the power supply. The burst of input capacitance is related to the quality of the input current of the power supply. Excessive burr voltage, high peak voltage, and unstable current all cause capacitors to charge and discharge too frequently. Capacitors that have been exposed to such working environments for a long time will experience a rapid increase in internal temperature. Exceeding the endurance limit of the explosion vent will result in slurry explosion.
For the output capacitor, as I mentioned C2, the current adjusted by the power module is filtered. The current here is filtered once, which is relatively stable, and the possibility of slurry explosion is relatively small. But if the ambient temperature is too high, the capacitor is also prone to slurry explosion. Explosion, report. Using garbage naturally leads to explosions and retribution.To know the cause of the past, see its present consequences; Those who want to know the future fruits see their present causes.
Reasons for electrolytic capacitor slurry explosion:
There are many reasons for capacitor surge, such as current exceeding the allowable stable wave current, voltage exceeding the working voltage, reverse voltage, frequent charging and discharging, etc. But the most direct reason is the high temperature. We know that an important parameter of a capacitor is its temperature resistance, which refers to the boiling point of the electrolyte inside the capacitor. When the internal temperature of the capacitor reaches the boiling point of the electrolyte, the electrolyte begins to boil, and the pressure inside the capacitor increases. When the pressure exceeds the limit of the explosion outlet, a slurry explosion occurs. So temperature is the direct cause of capacitor explosion. The designed service life of the capacitor is approximately 20000 hours, and it is also greatly affected by environmental temperature. The service life of capacitors decreases with the increase of temperature. Experiments have shown that for every 10 ℃ increase in ambient temperature, the service life of capacitors will be halved. The main reason is that temperature accelerates chemical reactions, causing the medium to degrade and fail over time, thus ending the lifespan of the capacitor. To ensure the stability of the capacitor, it needs to undergo a long-term high-temperature environment test before being inserted into the board. Even at 100 ℃, high-quality capacitors can work for thousands of hours. At the same time, the lifespan of the capacitor we mentioned refers to the capacity of the capacitor not exceeding 10% of the standard range change during use. Capacitor lifespan refers to the issue of capacitor capacity, rather than the occurrence of explosion after the design lifespan is reached. It just cannot guarantee the capacity standard of the capacitor design.
So, in a short period of time, the normal use of board capacitors will experience slurry explosion, which is a problem with capacitor quality. In addition, abnormal usage may also lead to capacitor explosion. For example, hot swapping computer accessories can also cause drastic changes in the local circuit current and voltage of the board, leading to capacitor usage failures.